Question 1

ABS

Accepted Answer

Anti-lock Braking System designed to prevent wheels from locking up during braking.

Question 2

Adventure bike

Accepted Answer

A type of motorcycle designed for long-distance travel on various terrains.

Question 3

Apex

Accepted Answer

The point at which the rider reaches the inside edge of a turn.

Question 4

Blind spot

Accepted Answer

Area around a vehicle where the driver's view is obstructed.

Question 5

Camber

Accepted Answer

The angle of the road surface in relation to the vertical plane.

Question 6

Carburetor

Accepted Answer

Device that mixes air and fuel for combustion in older motorcycles.

Question 7

Clutch lever

Accepted Answer

Hand-operated lever that engages or disengages the clutch.

Question 8

Countersteering

Accepted Answer

Technique used to initiate lean in a motorcycle by pushing on the handlebar in the opposite direction of the intended turn.

Question 9

Displacement

Accepted Answer

The total volume of all cylinders in an engine measured in cubic centimeters (cc) or liters (L).

Question 10

Drag coefficient

Accepted Answer

Measure of a motorcycle's resistance to the air as it moves forward.

Question 11

Exhaust system

Accepted Answer

System that carries exhaust gases from the engine to the rear of the motorcycle.

Question 12

Foot pegs

Accepted Answer

Metal pegs located on both sides of the motorcycle for resting the rider's feet.

Question 13

Friction zone

Accepted Answer

The area of the clutch engagement where the clutch begins to transmit power to the rear wheel.

Question 14

Gear shifting

Accepted Answer

The process of changing gears to match the speed and power requirements.

Question 15

Headlight modulator

Accepted Answer

Device that makes the motorcycle's headlight flash to increase visibility.

Question 16

Helmet

Accepted Answer

Protective headgear worn by motorcycle riders to reduce head injuries in the event of a crash.

Question 17

Highway bars

Accepted Answer

Metal bars mounted to the front and sides of a motorcycle to protect the engine and rider during a fall.

Question 18

Ignition system

Accepted Answer

System responsible for producing and delivering the high-voltage spark to the spark plugs.

Question 19

Inertial dampers

Accepted Answer

Devices used to stabilize the movement of the motorcycle during acceleration, deceleration, and cornering.

Question 20

Leaning

Accepted Answer

The act of inclining the motorcycle into a turn to maintain balance and negotiate curves.

Question 21

Lane splitting

Accepted Answer

The practice of riding between lanes of stopped or slow-moving traffic.

Question 22

Mirrors

Accepted Answer

Reflective devices attached to the handlebars or fairings to provide rearward visibility.

Question 23

Motorcycle endorsement

Accepted Answer

An additional license or endorsement required to legally operate a motorcycle.

Question 24

Neutral

Accepted Answer

A gear position where the engine is disengaged from the transmission.

Question 25

Oil cooler

Accepted Answer

Device used to cool the engine oil to maintain optimal operating temperature.

Question 26

Panniers

Accepted Answer

Detachable bags attached to the sides of a motorcycle for carrying luggage or gear.

Question 27

Quick-release fasteners

Accepted Answer

Fasteners that allow for quick and easy removal of components without the need for tools.

Question 28

Rev limiter

Accepted Answer

Electronic or mechanical device that limits the maximum engine speed to prevent damage.

Question 29

Saddlebags

Accepted Answer

Bags attached to the rear of a motorcycle for carrying personal items or gear.

Question 30

Side stand

Accepted Answer

A retractable stand on the side of a motorcycle used for parking and stability when not in motion.

Question 31

Skid

Accepted Answer

Loss of traction between the tires and the road surface resulting in a sliding motion.

Question 32

Throttle

Accepted Answer

Control on the right handlebar that regulates the engine's power output.

Question 33

Torque

Accepted Answer

Rotational force produced by the engine, measured in pound-feet (lb-ft) or Newton-meters (Nm).

Question 34

Tread depth

Accepted Answer

Measurement of the depth of grooves in a tire's tread pattern.

Question 35

Twisties

Accepted Answer

A term used to describe winding or curvy roads, often preferred by motorcycle riders for their dynamic nature.

Question 36

Visibility

Accepted Answer

The ability of other road users to see a motorcycle and its rider.

Question 37

Windscreen

Accepted Answer

A protective shield attached to the front of a motorcycle to deflect wind and debris.

Question 38

Braking distance

Accepted Answer

The distance a motorcycle travels from the moment the brakes are applied until it comes to a complete stop.

Question 39

Chain drive

Accepted Answer

A method of transmitting power from the engine to the rear wheel using a chain and sprockets.

Question 40

Crosswalk

Accepted Answer

Designated area for pedestrians to cross the road safely.

Question 41

Engine displacement

Accepted Answer

The total volume swept by all the pistons inside the cylinders of an engine.

Question 42

Handlebar grip

Accepted Answer

The rubber covering on the handlebars that provides grip and control.

Question 43

Helmet laws

Accepted Answer

Laws that require motorcycle riders to wear helmets for safety.

Question 44

Lane position

Accepted Answer

The placement of a motorcycle within a lane for optimal visibility and safety.

Question 45

Muffler

Accepted Answer

A device used to reduce the noise produced by the exhaust gases of the engine.

Question 46

Pre-ride inspection

Accepted Answer

A thorough check of the motorcycle's components and systems before each ride.

Question 47

Quick stop

Accepted Answer

An emergency braking technique to stop the motorcycle quickly while maintaining control.

Question 48

Road hazard

Accepted Answer

Any condition on the road that poses a potential danger to motorcyclists, such as potholes, debris, or oil spills.

Question 49

Sprocket

Accepted Answer

A toothed wheel connected to the motorcycle's chain to transfer power between the engine and rear wheel.

Question 50

Target fixation

Accepted Answer

A phenomenon where riders focus on an object they want to avoid, often leading to a loss of control.

Question 51

Throttle control

Accepted Answer

The skill of smoothly and precisely controlling the throttle to maintain speed and balance.

Question 52

Traffic signs

Accepted Answer

Signs on the road that provide information, warnings, and regulations for road users.

Question 53

Turn signal

Accepted Answer

A blinking light located on the front and rear of the motorcycle to indicate a change in direction.

Question 54

Upshifting

Accepted Answer

Changing to a higher gear to increase speed and efficiency.

Question 55

Vibration

Accepted Answer

Oscillating motion or shaking felt through the handlebars, foot pegs, or seat of the motorcycle.

Question 56

Wet braking

Accepted Answer

Braking on a wet road surface, which requires increased distance and gentler application of the brakes.

Question 57

Yaw

Accepted Answer

The side-to-side movement or rotation of a motorcycle along its vertical axis.

Question 58

Apex clipping

Accepted Answer

The technique of riding close to the inside edge of a turn to achieve a smoother and faster line.

Question 59

Clutchless shifting

Accepted Answer

Changing gears without using the clutch lever by precisely timing throttle control and gear engagement.

Question 60

Doppler effect

Accepted Answer

The change in frequency or pitch of sound as a motorcycle approaches or passes an observer.

Question 61

Engine braking

Accepted Answer

Using the resistance of the engine to slow down the motorcycle by downshifting without using the brakes.

Question 62

Group riding

Accepted Answer

Riding in a formation or group, requiring communication, spacing, and coordination among riders.

Question 63

Heel-toe shifting

Accepted Answer

A technique that involves using the heel and toe to shift gears without repositioning the foot on the foot peg.

Question 64

Lowside

Accepted Answer

A type of motorcycle crash where the bike slides out from under the rider due to loss of traction.

US New Mexico Motorcycle License Flashcard Set